Dramm Irrigation Products have been a staple in greenhouses throughout the world for decades. Our popular products like the Pin-Perfect Nozzle, the Nifty-Nozzle and the Dribble Tube are still available and work in a number of situations.
Each of these items is listed below.
For more on our newer systems, please visit their individual pages listed above.
The perfect overhead watering nozzle for foliage plants, bedding plants, geraniums and all 4 to 6 pot crops. Pin-Perfect Nozzles can be easily turned ÃÃoffÃ_ by pushing the pin down and ÃÃonÃ_ again by pulling the pin up. Each nozzle produces a 10 foot diameter spray pattern when your water pipeline is 5 feet above the crop.
Pin-Perfect Nozzles should be installed on the topside of the pipeline or on top of 1/2 PVC risers. For uniform coverage, Pin-Perfect Nozzles should be spaced so that their spray patterns overlap. With the pipeline at 5 feet over the crop your Pin-Perfect Nozzles will produce a 10 foot diameter spray pattern. Space each nozzle 5 feet apart so the spray pattern will overlap to the next nozzle. Multiple pipelines should be spaced 10 feet apart for complete coverage. To decrease the spray diameter of the Pin-Perfect to 7 feet, lower the water pipeline to 3 feet over the crop and space the nozzles at 3 1/2 foot intervals.
To compensate for pressure loss and ensures uniform water distribution, simply change the color coded nozzle to the nozzle with the next higher output rate. This changing of nozzles will compensate for pressure loss and produce approximately the same amount of output all the way down the pipeline. As a rule of thumb, we recommend changing color coded nozzles every (6th) sixth nozzle.
Before you begin an installation, we recommend that you install one pipeline based on the guidelines presented. After the first pipeline is installed, tested and adjusted, remaining lines can be set-up following the same specifications as the first.
Use Pin-Perfect Nozzles in combination with Dramm Run-Out Valves, No-Drip Risers and No-Drip Extension Check Valves to control water drip.
ITEM | COLOR | SIZE | 15 PSI | 22 PSI | 29 PSI | 36 PSI |
PPN-BR | Brown | 2.55 mm | 0.61 | 0.74 | 0.85 | 0.95 |
ITEM | COLOR | SIZE | 15 PSI | 22 PSI | 29 PSI | 36 PSI |
PPN-GN | Green | 2.65 mm | 0.69 | 0.82 | 0.95 | 1.08 |
PPN-GR | Grey | 2.75 mm | 0.77 | 0.9 | 1.03 | 1.17 |
PPN-BL | Blue | 2.80 mm | 0.79 | 0.95 | 1.11 | 1.27 |
PPN-RD | Red | 2.95 mm | 0.87 | 1.03 | 1.21 | 1.4 |
PPN-OR | Orange | 3.05 mm | 0.9 | 1.11 | 1.29 | 1.48 |
PPN-BK | Black | 3.25 mm | 0.98 | 1.21 | 1.4 | 1.6 |
Replacement pin for the Pin-Perfect Nozzle. The color of the pin designates the nozzle output rate. Replace pins with the same color as the original pin color. The diameter of the orifice in the black body of the Pin-Perfect Nozzle determines the flow rate for that nozzle. All pins have the same diameter and do not affect flow rate. Specify two letter color code when ordering.
ITEM | COLOR | SIZE |
PPNP-360 | - | - |
The Dramm 180_ Pin replaces any color pin on the Pin Perfect Nozzles. This allows for a 180_ pattern without changing nozzles. As the flow rate for the Pin Perfect Nozzle is controlled by the diameter of the nozzle body. The 180_ Pin offers a 180_ pattern without changing the flow. Color: black.
ITEM | COLOR | SIZE |
PPNP-180 | - | - |
Dramm 360_ Nifty Nozzles offer an economical solution for simple ÃÃoverheadÃ_ or ÃÃon the benchÃ_ watering systems. These ÃÃniftyÃ_ nozzles produce a 10 foot diameter spray pattern when your water pipeline is 5 feet above the crop. Nifty Nozzles can be installed on the topside of the pipeline, on bottom side of the pipeline or on top of 1/2 PVC risers. Bottom side installations require No-Drip Check Valves to prevent drip.
To provide uniform coverage the nozzles should be spaced so that their spray patterns overlap. With the pipeline 5 feet over your crop, Nifty Nozzles will produce a 10 foot diameter spray pattern. Space each nozzle 5 feet apart so the spray pattern will overlap to the next nozzle. Multiple pipelines should be spaced 10 feet apart for complete coverage. To decrease the spray diameter of the Nifty Nozzle to 7 feet, lower the water pipeline to 3 feet over the crop and space the nozzles at 3 1/2 foot intervals. Multiple pipelines should be spaced 7 feet apart for complete coverage.
For ÃÃon-the-benchÃ_ watering (for cut flower crops), we recommend using lower flow rate Brown, Green or Grey Nifty Nozzles spaced 3 feet apart, one pipeline down the center of each bench or bed.
Before you begin an installation, we recommend that you install one pipeline based on the guidelines presented. After the first pipeline is installed, tested and adjusted, remaining lines can be set-up following the same specifications as the first.
Use 360_ Nifty Nozzles in combination with Dramm Run-Out Valves, No-Drip Risers and No-Drip Extension Check Valves to control water drip.
ITEM | COLOR | SIZE | 15 PSI | 22 PSI | 29 PSI | 36 PSI |
360NN-BR | Brown | 1.75 mm | 0.29 | 0.35 | 0.41 | 0.46 |
ITEM | COLOR | SIZE | 15 PSI | 22 PSI | 29 PSI | 36 PSI |
360NN-GN | Green | 2.00 mm | 0.4 | 0.49 | 0.57 | 0.63 |
360NN-GR | Grey | 2.25 mm | 0.51 | 0.62 | 0.72 | 0.8 |
360NN-BL | Blue | 2.50 mm | 0.63 | 0.77 | 0.89 | 0.99 |
360NN-RD | Red | 2.75 mm | 0.76 | 0.93 | 1.07 | 1.2 |
360NN-OR | Orange | 3.00 mm | 0.9 | 1.1 | 1.28 | 1.43 |
An Assembly Insert is a threaded gasket that provides a quick installation and leak-free seal for Dramm Irrigation Nozzles. The interior female thread is 3/8 Witworth_ the same thread specification used on the Pin-Perfect, Nifty, Misty Mist and Drop style nozzles.
To Install, use a 7/16 drill bit to drill holes into schedule 40 PVC pipe, aluminum pipe or galvanized pipe. Caution: Do not use schedule 80 PVC. The Assembly Insert will not be able to create an effective seal due to the wall thickness of the schedule 80 PVC pipe.
Install the Assembly Insert into the hole and then screw in the nozzle. The width of the nozzle expands the Assembly Insert as it is screwed into place_ creating a leak-free seal without having to drill and tap every hole. Pipes should be clamped and drilled using a drill press or alignment jig to ensure perfectly round holes and straight alignment. Recommended for use at operating pressures up to 50 PSI.
ITEM | COLOR | SIZE |
AI | - | - |
Dramm 360_ Misty Mist Nozzles are for overhead mist propagation, irrigating plugs or raising humidity levels. Misty Mist Nozzles produce a 6 foot diameter spray pattern when your water pipeline is 5 feet above the crop.
Misty Mist Nozzles can be installed on the topside of the pipeline, on bottom side of the pipeline or on top of 1/2 PVC risers. Bottom side installations require No-Drip Check Valves to prevent drip.
To provide uniform coverage in overhead mist propagation or plug irrigation, the nozzles should be spaced so that their spray patterns overlap. With the pipeline 5 feet over your crop, Misty Mist Nozzles will produce a 6 foot diameter spray pattern. Space each nozzle 3 feet apart so the spray pattern will overlap to the next nozzle. Multiple pipelines should be spaced 6 feet apart for complete coverage. To decrease the spray diameter of the Misty Mist to 5 feet, lower the water pipeline to 3 feet over the crop and space the nozzles at 2 1/2 foot intervals. Multiple pipelines should be spaced 5 feet apart for complete coverage.
For raising humidity levels or mist cooling, use Blue/White Misty Mist Nozzles. It is recommended that you automate the system using short ÃÃonÃ_ cycle times due the relatively high output rate of the nozzle. The pipeline should be suspended as high as possible in the middle of each bay without interfering with the spray pattern. Space nozzles 6 feet apart. There is no need to worry about overlapping spray patterns since the goal is to evaporate water into the air versus allowing the water to drop to the soil.
Before you begin an installation, we recommend that you install one pipeline based on the guidelines presented. After the first pipeline is installed, tested and adjusted, remaining lines can be set-up following the same specifications as the first.
Use 360_ Misty Mist Nozzles in combination with Dramm Run-Out Valves, No-Drip Risers and No-Drip Extension Check Valves to control water drip.
ITEM | COLOR | SIZE | 36 PSI | 73 PSI |
MM-BW | Blue / White | 1.00 mm | 0.17 | 0.22 |
ITEM | COLOR | SIZE | 36 PSI | 73 PSI |
MM-RW | Red / White | 1.25 mm | 0.27 | 0.35 |
MM-KW | Black / White | 1.50 mm | 0.39 | 0.5 |
The High Pressure Misty Mist delivers an ultra fine spray_ ideal for mist cooling and raising humidity levels. These nozzles create a 10 foot diameter spray pattern.
High Pressure Misty Mist Nozzles should only be installed on the topside of the pipeline. Bottom side installations are not recommended due to the high pressures involved.
Space nozzles 10 feet apart with the pipeline suspended as high as possible in the middle of each bay_ without interfering with the spray pattern of the nozzle. There is no need to worry about overlapping spray patterns since the goal is to evaporate water into the air versus allowing the water to drop to the soil.
Please note that high pressure pumps and filtration equipment are required for these nozzles to work properly. High Pressure Misty Mist Nozzles can not be installed using Assembly Inserts. Threads must be tapped directly into the water pipeline_ use the drill & tap installation method explained at the end of this section.
Before you begin an installation, we recommend that you install one pipeline based on the guidelines presented. After the first pipeline is installed, tested and adjusted, remaining lines can be set-up following the same specifications as the first.
Use High Pressure 360_ Misty Mist Nozzles in combination with Dramm Run-Out Valves to control water drip.
ITEM | COLOR | SIZE | 73 PSI | 145 PSI | 290 PSI | 435 PSI |
HP-GW | Grey / White | 0.75 mm | 0.12 | 0.19 | 0.24 | 0.27 |
Due to a special spinning mechanism which increases the spray diameter of the Drop Inversion Nozzle_ it is perfect for 24 foot wide quonset/ tunnel houses. It is used on overhead watering systems that require a larger droplet size or an extended coverage area from each nozzle. Drop Inversion Nozzles produce a 360_ 24 foot diameter spray pattern and must be installed on the bottom side of the pipeline with No-Drip Extension Check Valves.
To provide uniform coverage the nozzles should be spaced so that their spray patterns overlap. With the pipeline 5 feet over your crop, Drop Inversion Nozzles produce a 24 foot diameter spray pattern. Space each nozzle 12 feet apart so the spray pattern will overlap to the next nozzle. Multiple pipelines should be spaced 24 feet apart for complete coverage. To decrease the spray diameter, lower the water pipeline until the desired spray diameter is achieved.
Before you begin an installation, we recommend that you install one pipeline based on the guidelines presented. After the first pipeline is installed, tested and adjusted, remaining lines can be set-up following the same specifications as the first.
Use Drop Inversion Nozzles in combination with Dramm Run-Out Valves and No-Drip Extension Check Valves to control water drip.
ITEM | COLOR | SIZE | 22 PSI | 29 PSI | 36 PSI |
DDI-GG | Grey / Grey | 2.25 mm | 0.62 | 0.71 | 0.8 |
The Drop Upright Nozzle has a unique spinning mechanism which increases the spray diameter of this nozzle to 30 feet when your water pipeline is 5 feet above the crop. It is used on overhead watering systems that require a larger droplet size or an extended coverage area from each nozzle. Drop Upright Nozzles produce a 360_ 36 foot diameter spray pattern and must be installed on the topside of the pipeline or on top of 1/2 PVC risers.
To provide uniform coverage the nozzles should be spaced so that their spray patterns overlap. With the pipeline 5 feet over your crop, Drop Upright Nozzles produce a 30 foot diameter spray pattern. Space each nozzle 15 feet apart so the spray pattern will overlap to the next nozzle. Multiple pipelines should be spaced 30 feet apart for complete coverage. To decrease the spray diameter, lower the water pipeline until the desired spray diameter is achieved.
Before you begin an installation, we recommend that you install one pipeline based on the guidelines presented. After the first pipeline is installed, tested and adjusted, remaining lines can be set-up following the same specifications as the first.
Use Drop Upright Nozzles in combination with Dramm Run-Out Valves, No-Drip Risers and No-Drip Extension Check Valves to control water drip.
ITEM | COLOR | SIZE | 22 PSI | 29 PSI | 36 PSI |
DDU-GB | Grey / Black | 2.25 mm | 0.62 | 0.71 | 0.8 |
The T-Drop Nozzle was created for long narrow installations in which an elliptical spray pattern is desired. T-Drop Nozzles can be installed on the topside of the pipeline, on bottom side of the pipeline or on top of 1/2 PVC risers. Bottom side installations require No-Drip Check Valves to prevent drip.
To provide uniform coverage the nozzles should be spaced so that their spray patterns overlap. With the pipeline 5 feet over your crop and nozzles installed on the topside of your pipeline, T-Drop Nozzles will produce a 10 foot by 5 foot elliptical spray pattern. Space each nozzle 5 feet apart so the spray pattern will overlap to the next nozzle. Multiple pipelines should be spaced 5 feet apart for complete coverage. To increase the spray diameter of the T-Drop to 12 feet by 6 feet, install the nozzles on the bottom side of the pipeline and space the nozzles at 6 foot intervals. Multiple pipelines should be spaced 6 feet apart for complete coverage.
Before you begin an installation, we recommend that you install one pipeline based on the guidelines presented. After the first pipeline is installed, tested and adjusted, remaining lines can be set-up following the same specifications as the first.
Use T-Drop Nozzles in combination with Dramm Run-Out Valves, No-Drip Risers and No-Drip Extension Check Valves to control water drip.
ITEM | COLOR | SIZE | 15 PSI | 22 PSI | 29 PSI | 36 PSI |
TDN | Brown / Red | 1.75 mm | 0.29 | 0.35 | 0.41 | 0.46 |
Oops! Did you drill one too many holes? Use the Dramm Nozzle Plug to cap off unwanted holes without replacing entire pipelines. Install as you would any other Dramm Nozzle or unscrew the unwanted Pin-Perfect, Nifty or Misty Mist Nozzle and simply replace it with the Nozzle Plug. Order a few extra_ we won't tell. Item Number: PLUG
ITEM | COLOR | SIZE |
PLUG | White | Universal |
The Dramm Hanging Nozzle system combines the superior flow rates and water patterns of Dramm nozzles with the flexibility of a below basket hanging irrigation system. Designed for misting or irrigation of crops on benches or on the ground, the Hanging Nozzle system uses the familiar Dramm nozzles with our No Drip Extension Check Valve and a leader tube.
Hanging nozzle systems offer solutions to the traditional problems of rigid pipe mounted irrigation systems. Hanging nozzle systems use a check valve and hang below the lateral which prevents dripping from the nozzle or the ÃÃshadowÃ_ dripping from the lateral. Dramm Hanging Nozzle Assemblies offer even watering. Gravity ensures that the nozzles are plumb preventing pattern distortion.
The entire assembly includes a leader tube with a barb fitting. The system uses flexible polyethylene tubing instead of PVC for ease of use and flexibility. A variety of leader tube lengths and nozzle choices are available. For flow rates see the specific nozzles.
To install a Dramm Pin-Perfect Hanging Nozzle System. Space the nozzle assemblies at 3_Ã spacings . Choose a leader tube length that places the nozzles below the hanging baskets or at a height of at least 3_Ã above the crop. Choose a Pin-Perfect Nozzle to suit your needs taking into account the flow rate of each nozzle and the flow rate of the lateral.
ITEM | COLOR | SIZE |
HNP-__-36 | - | 36 inch |
ITEM | COLOR | SIZE |
HNP-__-48 | - | 48 inch |
HNP-__-60 | - | 60 inch |
180_ spray pattern. Push into flexible 1/2 black poly tubing for perimeter watering. Use in conjunction with 90_ Nylon Nozzle.
ITEM | COLOR | SIZE |
180NY-RD | Red | - |
90_ spray pattern. Push into flexible 1/2 black poly tubing for perimeter watering. Use in conjunction with 180_ Nylon Nozzle.
ITEM | COLOR | SIZE |
90NY-GR | Grey | - |
No-Drip Risers elevate Dramm Irrigation Nozzles 2 1/4 above the PVC pipeline. When pipeline water flow is shut-off, excess water falls back into the pipeline due to the height of the No-Drip Riser. This ÃÃfall backÃ_ helps control drip from nozzles overhead. No-Drip Risers can also be used to elevate Dramm Irrigation Nozzles above the soil line when pipes are buried for landscape purposes.
ITEM | COLOR | SIZE |
NDR | - | - |
No-Drip Risers elevate Dramm Irrigation Nozzles 2 1/4 above the PVC pipeline. When pipeline water flow is shut-off, excess water falls back into the pipeline due to the height of the No-Drip Riser. This ÃÃfall backÃ_ helps control drip from nozzles overhead. No-Drip Risers can also be used to elevate Dramm Irrigation Nozzles above the soil line when pipes are buried for landscape purposes.
ITEM | COLOR | SIZE |
NDECV | - | - |
Run-Out Valves are designed to be installed at the end of 1-inch or 3/4-inch PVC pipelines. When the water is turned off, the Run-Out Valve will open and allow water to run out of the line_ eliminating drip from all overhead nozzles. Run-Out Valves require at least 15 PSI to work properly.
Use PVC cement and a 1 to 3/4 PVC reducer bushing to connect Run-Out Valves to 3/4-inch PVC pipelines. Follow the PVC cement directions regarding pipe preparation and drying times.
ITEM | COLOR | SIZE |
ROV | - | - |
The Threaded Pipe Nipple is used to attach Dramm Irrigation Nozzles directly to 1/2 PVC pipe risers. To install, simply screw the Threaded Pipe Nipple onto the threaded 1/2 PVC pipe riser. This method is ideal when you want to eliminate overhead lines or when overhead lines are impossible. 1/2 NPT X 3/8 WW . Use with 1/2 threaded PVC risers.
ITEM | COLOR | SIZE |
PN-2010 | - | - |
The Slip Fit Pipe Nipple is used to attach Dramm Irrigation Nozzles directly to straight (unthreaded) 1/2 PVC pipe risers. To install, use PVC cement to attach the Slip Fit Pipe Nipple onto PVC pipe risers. Follow the PVC cement directions regarding pipe preparation and drying times. This method is ideal when you want to eliminate overhead lines or when overhead lines are impossible. 1/2 NPT X 3/8 WW . Use with 1/2 straight PVC risers.
ITEM | COLOR | SIZE |
PN-2020 | - | - |
Creates a 3/8 Whitworth thread in PVC for Pin-Perfect, Nifty or Misty Mist Nozzles.
ITEM | COLOR | SIZE |
DT-N | - | - |
The Kwik Klamp is a bracket with a hinged clip that can open and close. This handy device locks shut when closed, but can be opened to remove or replace pipelines. The Kwik Klamp makes pipe installation fast and easy. Made in the Netherlands from chemical resistant polypropylene. Available for 3/4 and 1 diameter pipes. Metric and additional inch sizes are available upon special order. Use with the Kwik Spacer.
ITEM | COLOR | SIZE |
KK-75 | - | 3/4 in |
ITEM | COLOR | SIZE |
KK-100 | - | 1 in |
KK-125 | - | 1.25 in |
KK-150 | - | 1.5 in |
KK-200 | - | 2 in |
The Kwik Spacer slides into the Kwik Klamp and is used to create additional space between the pipe and wall. Multiple Kwik Spacers can be combined to create varying lengths in 3/4 increments. Made in the Netherlands from chemical resistant polypropylene. Available for 3/4 and 1 Kwik Klamps. Metric and additional inch sizes are available upon special order.
ITEM | COLOR | SIZE |
KS-75 | - | 3/4 in |
ITEM | COLOR | SIZE |
KS-100 | - | 1 in |
KS-125 | - | 1.25 in |
KS-150 | - | 1.5 in |
KS-200 | - | 2 in |
Dramm On Only Dribble Tubes have permanently attached always ON weight emitters. All On Dribble Tubes are permanently assembled. Different sizes and different lengths can be combined for price breaks.
There are three types of Dribble Tubes available: DTS with a .045 inside diameter green tube, DTM with a .060 inside diameter brown tube- and DTL with a .075 inside diameter blue tube. All 3 types are available in lengths from 12 TO 42 long. Use of Dribble Tubes allows individual pot watering for a total bench. Dramm Dribble Tubes should be used on 5, 6, or 7 pot sizes.
ITEM | COLOR | SIZE |
DTS-12 | Green Tubing | 12 in |
ITEM | COLOR | SIZE |
DTS-18 | Green Tubing | 18 in |
DTS-24 | Green Tubing | 24 in |
DTS-30 | Green Tubing | 30 in |
DTS-36 | Green Tubing | 36 in |
DTS-42 | Green Tubing | 42 in |
DTS-48 | Green Tubing | 48 in |
DTS-60 | Green Tubing | 60 in |
DTM-12 | Brown Tubing | 12 in |
DTM-18 | Brown Tubing | 18 in |
DTM-24 | Brown Tubing | 24 in |
DTM-30 | Brown Tubing | 30 in |
DTM-36 | Brown Tubing | 36 in |
DTM-42 | Brown Tubing | 42 in |
DTM-48 | Brown Tubing | 48 in |
DTM-60 | Brown Tubing | 60 in |
DTL-12 | Blue Tubing | 12 in |
DTL-18 | Blue Tubing | 18 in |
DTL-24 | Blue Tubing | 24 in |
DTL-30 | Blue Tubing | 30 in |
DTL-36 | Blue Tubing | 36 in |
DTL-42 | Blue Tubing | 42 in |
DTL-48 | Blue Tubing | 48 in |
DTL-60 | Blue Tubing | 60 in |
Dramm StixÃ_ are designed to be used when it is impossible to run overhead water lines but the grower wants to water or mist from overhead. Very useful on moveable benching! Dramm Stix are available in 5 different heights from 10 to 36 and include the poly tubing (-which is 30 longer than the stick-), Pin Perfect nozzles, and the Dramm Stixé. The orange base Dramm Stixsé allow you to change from water nozzles to mist nozzles.
Dramm Stixé have a 3/8 WW thread which accommodates the Pin Perfect, Nifty, Misty Mist, and 180_ Nifty Nozzles. Dramm stix come standard with green Pin Perfect Nozzles unless specific type and color-coded nozzle are requested. Nifty Nozzles spray a 7 ft. diameter circle- while Misty Mist Nozzles cover a 4.5 ft. diameter circle. Both will completely water 100 ft. of bench or bed in about 5 minutes. Water supply tubes are inserted at 42 inch intervals in 3/4 or 1 black polyethylene pipe. Benches up to 70ft. long- use 3/4 pipe, over 70 ft. long- use 1 pipe, over 120 ft. long- use 1 pipe with supply in middle.
ITEM | COLOR | SIZE |
SS-10 | - | 10 in |
ITEM | COLOR | SIZE |
SS-16 | - | 16 in |
SS-24 | - | 24 in |
SS-30 | - | 30 in |
SS-36 | - | 36 in |
Dramm Dribble Rings are designed for individual pot watering of larger size containers. The ring encircles the plant and water is emitted in 5 areas through 10 holes to ensure uniform watering in larger pot sizes. Dribble Rings come in 5 sizes with different length lead tubes: They are recommended for all plants in 6 & 7 containers, 8 - 10 containers, 13 containers, 16 containers, and the largest for use in 18 - 20 containers. Dramm Dribble Rings provide complete, uniform watering for large pots, B&B stock, tropical plantings and orchids.
Dribble Rings are fed with a .060 ID Tube. A maximum of 400 containers can be watered with the Dramm Dribble Rings from a 3/4 supply pipe. Minimum order 100 per size.
ITEM | COLOR | SIZE |
DR4-12 | - | 12 in |
ITEM | COLOR | SIZE |
DR4-24 | - | 24 in |
DR4-36 | - | 36 in |
DR4-48 | - | 48 in |
DR6-12 | - | 12 in |
DR6-24 | - | 24 in |
DR6-36 | - | 36 in |
DR6-48 | - | 48 in |
DR85-12 | - | 12 in |
DR85-24 | - | 24 in |
DR85-36 | - | 36 in |
DR85-48 | - | 48 in |
DR10-12 | - | 12 |
DR10-24 | - | 24 |
DR10-36 | - | 36 |
DR10-48 | - | 48 |
DR13-12 | - | 12 |
DR13-24 | - | 24 |
DR13-36 | - | 36 |
DR13-48 | - | 48 |
The Dramm Hand Pick Tool is used for the insertion of Dramm Brass Eyelets into poly tubbing for the use of Dramm Dribble Tubes and Rings. Place an eyelet onto the tip of the Handpik tool and push firmly into the black poly tubing. The Hand Pick Tool will pierce the poly tubing and insert the brass eyelet in one leak-free operation!
ITEM | COLOR | SIZE |
HPT | - | - |
Brass eyelet. Used to install Dramm Dribble Tubes and Dribble Rings.
ITEM | COLOR | SIZE |
DTMS-E | - | .060 or .045 ID |
Brass eyelet. Used to install Dramm Dribble Tubes and Dribble Rings.
ITEM | COLOR | SIZE |
DTL-E | - | .075 ID |
Small leader tube for Dramm Dribble Tubes.
ITEM | COLOR | SIZE |
O45 | Green | 5,000 feet/ roll |
Medium leader tube for Dramm Dribble Tubes.
ITEM | COLOR | SIZE |
O6O | Brown | 5,000 feet/ roll |
Large leader tube for Dramm Dribble Tubes.
ITEM | COLOR | SIZE |
O75 | Blue | 5,000 feet/ roll |
Dramm Stix leader tube.
ITEM | COLOR | SIZE |
192 | Black | 2,500 feet/ roll |
Dramm's ultra-durable solenoids are designed to outlast the competition and shut-off rapidly. Perfect for misting systems, where an extra second or two is more water than needed, the SVB range of solenoids are fast acting.
ITEM | COLOR | SIZE |
SVB075 | - | 3/4 in - 24VAC 1.2 W |
Dramm Solenoid Valve - 1 National Pipe Thread
ITEM | COLOR | SIZE |
SVB100 | - | 1 in - 24VAC 1.2 W |
SVB150 | - | 1.5 in - 24VAC 1.2 W |
SVB200 | - | 2 in - 24VAC 1.2 W |
Dramm PE tubing is available in 16mm and 25mm (3/4) in various lengths. Call for sizing and pricing.
ITEM | COLOR | SIZE |
PE tubing | - | 16mm or 25mm |
Dramm offers preassembled valve stations as well as multi line manifolds. Build with easy maintenance in mind, Dramm pre assembled PVC components make irrigation system installation easy. Talk to Dramm about designing your irrigation system today and include Dramm pre assembled system components.
ITEM | COLOR | SIZE |
Valve Station | - | - |
PolyRail aluminum extrusion tightly sleeves PE tubing keeping it rigid, without sags. PolyRail keeps nozzles straight and even, ensuring the best coverage for your irrigation system. Installs easily without glue.
ITEM | COLOR | SIZE |
ALU16 | - | 12' section |
25mm (3/4) diameter. For higher flow and more support. 25mm PolyRail may be used to hang baskets
ITEM | COLOR | SIZE |
ALU25 | - | 12' section |
Connecting band with set screws. 4 length. Connects two rail pieces together.
ITEM | COLOR | SIZE |
ALU501CB | - | 4 inch |
Connecting band with set screws. 14 length. Connects two rail pieces together.
ITEM | COLOR | SIZE |
ALU50135 | - | 14 inch |
Hanger to position PE outlet at a 90_ angle
ITEM | COLOR | SIZE |
ALU500PH | - | 16mm |
Hanger to position PE outlet at a 90_ angle
ITEM | COLOR | SIZE |
ALU500-90 | - | 25mm |
Hanger rides on Rail to position PE outlet towards the bottom of the Rail.
ITEM | COLOR | SIZE |
ALU502H | - | Top |
Stop used at both ends of each irrigation run. Includes set screw.
ITEM | COLOR | SIZE |
ALU541S | - | - |
Punch for centering 3mm hole in PE.
ITEM | COLOR | SIZE |
ALU503A | - | 25mm |
Punch for centering 3mm hole in PE.
ITEM | COLOR | SIZE |
ALU509A | - | 16mm |
Base for PolyRail Bench Riser Support
ITEM | COLOR | SIZE |
ALUSB | - | - |
Cap for top of PolyRail Bench Riser Support
ITEM | COLOR | SIZE |
ALUSC | - | - |
JetRain Nozzle Low Pressure with Clean Out Check Valve Barbed Inlet. For propagation mist. Alternate with Blue for best results.
ITEM | COLOR | SIZE |
JRLPC-B-WH | - | .48 gpm |
JetRain Nozzle Low Pressure with Clean Out Check Valve Barbed Inlet. For propagation mist. Alternate with White for best results.
ITEM | COLOR | SIZE |
JRLPC-B-BL | - | .48 gpm |
JetRain Nozzle Low Pressure with Clean Out Check Valve Barbed Inlet. For mist and irrigation.
ITEM | COLOR | SIZE |
JRLPC-B-RD | - | .79 gpm |
JetRain Nozzle Low Pressure with Clean Out Check Valve Barbed Inlet. For heavier irrigation.
ITEM | COLOR | SIZE |
JRLPC-B-YL | - | 1.37 gpm |
JetRain Nozzle Barbed with no Check Valve Barbed Inlet
ITEM | COLOR | SIZE |
JR-B | - | - |
JetRain Nozzle Low Pressure with Clean Out Check Valve Threaded Inlet. For propagation mist. Alternate with Blue for best results.
ITEM | COLOR | SIZE |
JRLPC-T-WH | - | .48 gpm |
JetRain Nozzle Low Pressure with Clean Out Check Valve Threaded Inlet. For propagation mist. Alternate with White for best results.
ITEM | COLOR | SIZE |
JRLPC-T-BL | - | .48 gpm |
JetRain Nozzle Low Pressure with Clean Out Check Valve Threaded Inlet. For mist and irrigation.
ITEM | COLOR | SIZE |
JRLPC-T-RD | - | .79 gpm |
JetRain Nozzle Low Pressure with Clean Out Check Valve Threaded Inlet. For heavier irrigation.
ITEM | COLOR | SIZE |
JRLPC-T-YL | - | 1.37 gpm |
JetRain Nozzle Threaded with no Check Valve Threaded Inlet
ITEM | COLOR | SIZE |
JR-T | - | - |
JetRain 180 deg Pattern Barbed - Choose a color
ITEM | COLOR | SIZE |
JRLPC180-B-_ | - | - |
JRLPC180-T-_ | - | - |
JRC180-_ _ | - | - |
JR180-_ _ | - | - |
Replacement pin are specific to each nozzle. Please specify color when ordering.
ITEM | COLOR | SIZE |
JR-P-_ _ | - | - |
Check valve for JetRain nozzle with cleanout. 15-50 psi.
ITEM | COLOR | SIZE |
JR-807L | - | - |
Check valve for JetRain nozzle with cleanout. 15-50 psi.
ITEM | COLOR | SIZE |
JR-808L | - | - |
Jet Rain installation and care manual.
ITEM | COLOR | SIZE |
Manual | - | - |
JR-539 | - | - |
JR-566 | - | - |
JR-528 | - | - |
Add to a JetRain assembly to turn individual nozzles on and off.
ITEM | COLOR | SIZE |
JRBV-750 | - | - |
The JefFog nozzle offers a very fine spray (80 micron) between 50-70 psi. Available in a barbed or threaded inlet with single or multiple outlets. Flow per tip is 5.8 lph (1.5 gph).
ITEM | COLOR | SIZE |
JFSB | - | - |
The JefFog nozzle offers a very fine spray (80 micron) between 50-70 psi. Available in a barbed or threaded inlet with single or multiple outlets. Flow per tip is 5.8 lph (1.5 gph).
ITEM | COLOR | SIZE |
JFST | - | - |
Two outlet nozzle with barbed inlet. Flow rate is 11.6 lph (3 gph).
ITEM | COLOR | SIZE |
JFB2 | - | - |
Four outlet nozzle with barbed inlet. Flow rate is 23.2 lph (6 gph).
ITEM | COLOR | SIZE |
JFSB4 | - | - |
Five outlet nozzle with barbed inlet. Flow rate is 29 lph (7.5 gph).
ITEM | COLOR | SIZE |
JFSB5 | - | - |
Four outlet nozzle with threaded inlet. Flow rate is 23.2 lph (6 gph).
ITEM | COLOR | SIZE |
JFST4 | - | - |
Five outlet nozzle with threaded inlet. Flow rate is 29 lph (7.5 gph).
ITEM | COLOR | SIZE |
JFST5 | - | - |
Installation and care manual for JetFog nozzles.
ITEM | COLOR | SIZE |
Manual | - | - |
Replacement nozzle tip for JetFog nozzle. Press-fit connection.
ITEM | COLOR | SIZE |
JF-525 | - | - |
Blank nozzle tip to prevent spray from any JetFog outlet. Press-fit connection.
ITEM | COLOR | SIZE |
JF-524 | - | - |
Two way cross for JetFog Nozzle. Press fit connection.
ITEM | COLOR | SIZE |
JF-2CROSS | - | - |
Four way cross for JetFog Nozzle. Press fit connection.
ITEM | COLOR | SIZE |
JF-4CROSS | - | - |
Replacement diaphragm for JetFog Anti Drip Device. Silicone. Use JF-WRENCH-C to access diaphragm and reseat new diaphragm.
ITEM | COLOR | SIZE |
JF-560 | - | - |
Includes JF-WRENCH & BLANK tool, 10 BLANK6, 5 JF-525, 3 JF-524, 5 JF-560
ITEM | COLOR | SIZE |
JF-KIT | - | kit |
Combo set for disassembling and reassembling JetFOG nozzles easily.
ITEM | COLOR | SIZE |
JF-WRENCH-C | - | - |
The ii ri Smart Controller is a a battery operated, Bluetooth Connected, irrigation/misting controller that can oprate one solenoid valve without wiring.
Create different programs on your smartphone and upload them to your ii ri easily to change scenarios. Great for quick installations, single propagation benches, outdoor mum fields and more.
ITEM | COLOR | SIZE |
iiri3v | - | 3/4 in. valve |
Ii ri Smart Controller including 3/4 solenoid valve.
ITEM | COLOR | SIZE |
iiriSVB075 | - | 3/4 in. valve |
iiriSVB100 | - | 1 in. valve |
The Dramm MistTime Controller is perfect for time or temperature based control of misting valves. With the ability to program each valve independently, the MistTime offers unmatched flexibility. Each valve is operated on a cycle. The timing is variable with the duration operating between 1 second and 60 minutes and the interval time operating between 1 minute and 12 hours. Each valve can be run continuously, between specific times, or even started when the temperature rises above a set point. With the ability to program each valve independently, the controller can operate as a time based mist controller, a pulse-irrigation controller and a mist cooling controller at the same time. In addition, the MistTime offers the option to convert the last valve output to a pump pre-start output. When configured in this manner, the operator is given an option to pre-start a pump prior to any valve operation. The pre-start time is variable. This ensures that the system is properly pressurized when the mist system is in operation. The MistTime is easy to program using a keypad to navigate the menu and enter amounts. For flexibility, the MistTime can be programmed in English, Spanish, French or Dutch. The MistTime operates on 120vAC or 220vAC and includes a 24vAC output. The unit is enclosed in a NEMA 4 rated PVC housing and is easy to wire and install.
ITEM | COLOR | SIZE |
MT-10 | - | 10 Output |
The MistTime is programmable in English, Spanish, French and Dutch. This manual offers native language support.
ITEM | COLOR | SIZE |
MT-10 Manual ESP | - | - |
MT-10 Manual FRA | - | - |
MT10-TP | - | - |
The ProLine Irrigation Controller offers advanced control features such as multiple program operation, master valve, multiple start times per day, manual operation, and an option to add cellular connectivity to monitor and modify irrigation operation from your phone.
ITEM | COLOR | SIZE |
PL1600-04 | - | 4 output |
Quick Start Guide for the ProLine Controller. Step-by-step instructions to program the basics.
ITEM | COLOR | SIZE |
ProLineQS | - | Document |
Easy instructions showing how to install your ProLine Controller.
ITEM | COLOR | SIZE |
ProLineIG | - | Document |
ITEM | COLOR | SIZE |
PL1600-08 | - | 8 output |
PL1600-12 | - | 12 output |
PL1600-12B | - | 12 output (base) |
PL1600-16 | - | 16 output |
PL1600-20 | - | 20 output |
PL1600-24 | - | 24 output |
PL-1600-M4 | - | 4 output module |
PL-1600-M12 | - | 12 output module |
PL-SLAC | - | - |
PL-SLAC-50 | - | - |
PL-420LS | - | - |
The RainPro has been discontinued. The manual remains on line for previous customers.
ITEM | COLOR | SIZE |
RPIC-Manual | - | - |
The RainPro has been discontinued. However, we still have 4 output modules to upgrade existing units. This module fits into open slots in the RainPro 03, 07 and 11 version to add 4 outputs to increase the capacity of the unit.
ITEM | COLOR | SIZE |
RPIC-M4 | - | 4 Outputs |
ITEM | COLOR | SIZE |
PCAS2L-18 | - | 18 in |
ITEM | COLOR | SIZE |
PCAS2L-24 | - | 24 in |
PCAS2L-36 | - | 36 in |
PCAS2L-48 | - | 48 in |
2 liter per hour emitter with barbed outlet for attaching to 0.191 tubing. Offering even flow rates at variable pressures, PCAS emitters provide even water from the first to the last dripper. Our LARGER emitter body allows for a wider labyrinth that prevents clogging by letting debris pass through the emitter.
ITEM | COLOR | SIZE |
PCAS2L | - | 2 lph |
4 liter per hour emitter with barbed outlet for attaching to 0.191 tubing. Offering even flow rates at variable pressures, PCAS emitters provide even water from the first to the last dripper. Our LARGER emitter body allows for a wider labyrinth that prevents clogging by letting debris pass through the emitter.
ITEM | COLOR | SIZE |
PCAS4L | - | 4 lph |
4 liter per hour emitter with barrel outlet for attaching to 0.191 tubing. Offering even flow rates at variable pressures, PCAS emitters provide even water from the first to the last dripper. Our LARGER emitter body allows for a wider labyrinth that prevents clogging by letting debris pass through the emitter.
ITEM | COLOR | SIZE |
PCAS4L-B | - | 4 lph |
8 liter per hour emitter with barrel outlet for attaching to 0.191 tubing. Offering even flow rates at variable pressures, PCAS emitters provide even water from the first to the last dripper. Our LARGER emitter body allows for a wider labyrinth that prevents clogging by letting debris pass through the emitter.
ITEM | COLOR | SIZE |
PCAS8L | - | 8 lph |
12 liter per hour emitter with barrel outlet for attaching to 0.191 tubing. Offering even flow rates at variable pressures, PCAS emitters provide even water from the first to the last dripper. Our LARGER emitter body allows for a wider labyrinth that prevents clogging by letting debris pass through the emitter.
ITEM | COLOR | SIZE |
PCAS12L | - | 12 lph |
Connect barrel outlet emitters to 192 tubing with this adaptor.
ITEM | COLOR | SIZE |
MAN1 | - | 1 outlet 3mm barb |
Dramm 2 and 4 Way Manifolds are for use with the MB 4LPH and 8LPH emitters. The Manifolds allow multiple pots to be watered from one emitter.
ITEM | COLOR | SIZE |
MAN2 | - | 2 outlet 3mm barb |
Dramm 2 and 4 Way Manifolds are for use with the MB 4LPH and 8LPH emitters. The Manifolds allow multiple pots to be watered from one emitter.
ITEM | COLOR | SIZE |
MAN4 | - | 4 outlet 3mm barb |
ITEM | COLOR | SIZE |
PCASW | - | 11 Gram |
ITEM | COLOR | SIZE |
191-18 | Black | 18 in. |
191-24 | Black | 24 in. |
191-36 | Black | 35 in. |
191-42 | Black | 42 in. |
191-48 | Black | 48 in. |
Pressure Compensated Rings offer even watering of trees and nursery stock. With a choice of 4 lph (1 gph), 8 lph (2 gph), or 12 lph (4 gph) emitters, each plant gets the same amount of water supplied by Dramm's Dribble Rings.
ITEM | COLOR | SIZE |
PCR4-12 | - | 12 in. tube |
ITEM | COLOR | SIZE |
PCR4-24 | - | 24 in. tube |
PCR4-36 | - | 36 in. tube |
PCR4-48 | - | 48 in. tube |
PCR6-12 | - | 12 in. tube |
PCR6-24 | - | 24 in. tube |
PCR6-36 | - | 36 in. tube |
PCR6-48 | - | 48 in. tube |
PCR85-12 | - | 12 in. tube |
PCR85-24 | - | 24 in. tube |
PCR85-36 | - | 36 in. tube |
PCR85-48 | - | 48 in. tube |
PCR10-12 | - | 12 in. tube |
PCR10-24 | - | 24 in. tube |
PCR10-36 | - | 36 in. tube |
PCR10-48 | - | 48 in. tube |
PCR13-12 | - | 12 in. tube |
PCR13-24 | - | 24 in. tube |
PCR13-36 | - | 36 in. tube |
PCR13-48 | - | 48 in. tube |
The S3ANCHOR holds dribble rings in the pot, keeping them optimally placed for best water distribution.
ITEM | COLOR | SIZE |
S3ANCHOR | - | 6 |
The T-Piece has two barbed, secure connections and one smooth connection to allow for the ring to be easily disconnected.
ITEM | COLOR | SIZE |
T-PIECE | - | - |
Barbed Microvalve for drip irrigation. Allows individual pressure compensated drippers to be turned off.
ITEM | COLOR | SIZE |
MTMV-25 | - | 1/4 in barbs |
Barbed fitting
ITEM | COLOR | SIZE |
BARB3 | - | 3mm |
Plug for mistakes when using the 3mm barbed fitting.
ITEM | COLOR | SIZE |
BLANK3 | - | 3mm |
Multi-tool for irrigation installation. Cuts PE, punches holes with 3,4,5 mm blades. Inserts barbed components into PE.
ITEM | COLOR | SIZE |
ML-TOOL | - | Multi |
Easy-to-use 3mm Punch for 16mm or 1/2 Tubing
ITEM | COLOR | SIZE |
PUNCH1650 | - | 3mm |
Replaces standard blade when worn.
ITEM | COLOR | SIZE |
PUNCH1650-B | - | 3mm |
Plain barbed stake
ITEM | COLOR | SIZE |
ST-45 | - | 4 in. |
Labyrinth Stake
ITEM | COLOR | SIZE |
LST4-45 | - | 4 in. |
Easyloc Inline Valve 16mm x 16mm. Shuts off PE line. Insert as needed. Barb & Compression nut. Needs no additional clamp.
ITEM | COLOR | SIZE |
ITVSL16 | - | 16mm x 16mm |
Easyloc Inline Valve 16mm x 3/4in. MPT. Connect PVC to PE. Barb & Compression nut. Needs no additional clamp.
ITEM | COLOR | SIZE |
ITV075SL16 | - | 16mm x 3/4in |
Easyloc Fitting 16mm x 3/4in. MPT. Connect PVC to PE. Barb & Compression nut. Needs no additional clamp.
ITEM | COLOR | SIZE |
ITF075SL16 | - | 16mm x 3/4in |
Easyloc Tee 16mm. Barb & Compression nut. Needs no additional clamp.
ITEM | COLOR | SIZE |
ITTSL16 | - | 16mm |
Easyloc Elbow 16mm. Barb & Compression nut. Needs no additional clamp.
ITEM | COLOR | SIZE |
ITESL16 | - | 16mm |
Easyloc Coupling 16mm. Barb & Compression nut. Needs no additional clamp.
ITEM | COLOR | SIZE |
ITCSL16 | - | 16mm |
Figure 8 clamp to close 16mm PE ends.
ITEM | COLOR | SIZE |
600AP8 | - | 16mm |
Floraplus 2 (1L/m2 - cap mat & PP ground cover) 72 x 100' Roll
ITEM | COLOR | SIZE |
FP2-72X100 | - | 72 in |
FP3-72X100 | - | 72 in |
FP2-48X100 | - | 48 in |
FP3-48X100 | - | 48 in |
FP2-96X100 | - | 96 in |
Vivaplus 2 (3L/m2 - cap mat & PP ground cover)) 72 x 100' Roll
ITEM | COLOR | SIZE |
VP2-72X100 | - | 72 in |
VP3-72X100 | - | 72 in |
VP2-48X100 | - | 48 in |
VP3-48X100 | - | 48 in |
VP2-96X100 | - | 96 in |
Aquafol Filter Cloth - White 79 x 164' Roll
ITEM | COLOR | SIZE |
AFW-79X164 | - | 79 in |
AFW-48X100 | - | 48 in |
Strand Dripper 12 lph flow rate with 18 inch perforated tube.
ITEM | COLOR | SIZE |
ST18-A112 | - | 18 in |
ST24-A112 | - | 36 in |
ST30-A116 | - | 36 in |
ST42-A116 | - | 42 in |
ST30-A124 | - | 30 in |
ST42-A124 | - | 42 in |
STP12-A208 | - | 12 in |
STP18-A208 | - | 18 in |
STP18-A212 | - | 18 in |
STP24-A212 | - | 24 in |
STP30-A216 | - | 30 in |
STP42-A216 | - | 42 in |
STP30-A224 | - | 30 in |
STP42-A224 | - | 42 in |
#10,11,12,13,14,15,16,17,18,20 - Green #1, Black#2, Gray#3
ITEM | COLOR | SIZE |
N-12884-11XX | - | - |
#40, 45, 50, 55, 60 - Red #1 , White #2, Orange #7
ITEM | COLOR | SIZE |
N-9913-11XX | - | - |
#10,11,12,13,14,15,16,18,20 - Blue #10, Purple #12, Green #14, Red #16, Yellow #18, Brown #20 Purple, Ivory
ITEM | COLOR | SIZE |
N-9928-10XX | - | - |
#10,11,12,13,14,15,16,17,18,20 - Standard flat Black plate
ITEM | COLOR | SIZE |
N-12928-10XX | - | - |
N-9914-13XX | - | - |
N-12927-11XX | - | - |
N-9929-10XX | - | - |
N-13827-12XX | - | - |
ITEM | COLOR | SIZE |
N-12213-001 | - | - |
The Abot Riser base connects laterals to risers.
ITEM | COLOR | SIZE |
A-050-001-607 | - | 1.5 in |
Male PipeLoc fitting.
ITEM | COLOR | SIZE |
A-050-001-616 | - | 1.5 in |
Female PipeLoc fitting.
ITEM | COLOR | SIZE |
A-050-001-517 | - | 1.5 in |
20 inch riser section for PipeLoc. Threads into Riser Base and connects to other riser pipes to reach desired nozzle height.
ITEM | COLOR | SIZE |
A-032-032-450 | - | - |
ITEM | COLOR | SIZE |
A-063-001-607 | - | 2 in |
A-075-001-607 | - | 2.5 in |
A-090-001-607 | - | 3 in |
A-050-050-621 | - | 1.5 in |
A-063-063-623 | - | 2 in |
A-075-050-624 | - | 2.5 in/1.5 in |
A-075-063-625 | - | 2.5 in/2 in |
A-075-075-626 | - | 2.5 in |
A-090-050-627 | - | 3 in/1.5in |
A-090-063-628 | - | 3in/2in |
A-090-075-629 | - | 3in/2.5in |
A-090-090-630 | - | 3 in |
A-050-050-642 | - | 1.5 in |
A-063-063-644 | - | 2 in |
A-075-050-645 | - | 2.5 in/1.5 in |
A-075-063-646 | - | 2.5 in/2 in |
A-075-075-647 | - | 2.5 in |
A-090-050-648 | - | 3 in/1.5in |
A-090-063-649 | - | 3 in/2 in |
A-090-075-650 | - | 3 in/2.5 in |
A-090-090-651 | - | 3in |
A-063-050-665 | - | - |
A-075-050-666 | - | - |
A-075-063-667 | - | - |
A-090-050-668 | - | - |
A-090-063-669 | - | - |
A-090-075-670 | - | - |
A-050-000-608 | - | - |
A-063-000-608 | - | - |
A-075-000-608 | - | - |
A-090-000-608 | - | - |
A-050-000-509 | - | 1.5 in |
A-063-000-509 | - | 2 in |
A-075-000-509 | - | 2.5 in |
A-090-000-509 | - | 3 in |
A-063-001-616 | - | 2 in |
A-075-001-616 | - | 2.5 in |
A-090-001-616 | - | 3 in |
A-063-001-517 | - | 2 in |
A-075-001-517 | - | 2.5 in |
A-090-001-517 | - | 3 in |
A-050-000-605 | - | 1.5 in |
A-063-000-605 | - | 2 in |
A-075-000-605 | - | 2.5 in |
A-030-000-605 | - | 3 in |
A-050-000-506 | - | 1.5 in |
A-063-000-506 | - | 2 in |
A-075-000-506 | - | 2.5 in |
A-030-000-506 | - | 3 in |
A-032-025-001 | - | - |
A-032-032-014 | - | - |
A-050-000-612 | - | 1.5 in |
A-063-000-612 | - | 2 in |
A-075-000-612 | - | 2.5 in |
A-090-000-612 | - | 3 in |
Dramm Irrigation Products have been a staple in greenhouses throughout the world for decades. Our popular products like the Pin-Perfect Nozzle, the Nifty-Nozzle and the Dribble Tube are still available and work in a number of situations.
Each of these items is listed below.
For more on our newer systems, please visit their individual pages listed above.
The perfect overhead watering nozzle for foliage plants, bedding plants, geraniums and all 4 to 6 pot crops. Pin-Perfect Nozzles can be easily turned ÃÃoffÃ_ by pushing the pin down and ÃÃonÃ_ again by pulling the pin up. Each nozzle produces a 10 foot diameter spray pattern when your water pipeline is 5 feet above the crop.
Pin-Perfect Nozzles should be installed on the topside of the pipeline or on top of 1/2 PVC risers. For uniform coverage, Pin-Perfect Nozzles should be spaced so that their spray patterns overlap. With the pipeline at 5 feet over the crop your Pin-Perfect Nozzles will produce a 10 foot diameter spray pattern. Space each nozzle 5 feet apart so the spray pattern will overlap to the next nozzle. Multiple pipelines should be spaced 10 feet apart for complete coverage. To decrease the spray diameter of the Pin-Perfect to 7 feet, lower the water pipeline to 3 feet over the crop and space the nozzles at 3 1/2 foot intervals.
To compensate for pressure loss and ensures uniform water distribution, simply change the color coded nozzle to the nozzle with the next higher output rate. This changing of nozzles will compensate for pressure loss and produce approximately the same amount of output all the way down the pipeline. As a rule of thumb, we recommend changing color coded nozzles every (6th) sixth nozzle.
Before you begin an installation, we recommend that you install one pipeline based on the guidelines presented. After the first pipeline is installed, tested and adjusted, remaining lines can be set-up following the same specifications as the first.
Use Pin-Perfect Nozzles in combination with Dramm Run-Out Valves, No-Drip Risers and No-Drip Extension Check Valves to control water drip.
ITEM | COLOR | SIZE | 15 PSI | 22 PSI | 29 PSI | 36 PSI |
PPN-BR | Brown | 2.55 mm | 0.61 | 0.74 | 0.85 | 0.95 |
ITEM | COLOR | SIZE | 15 PSI | 22 PSI | 29 PSI | 36 PSI |
PPN-GN | Green | 2.65 mm | 0.69 | 0.82 | 0.95 | 1.08 |
PPN-GR | Grey | 2.75 mm | 0.77 | 0.9 | 1.03 | 1.17 |
PPN-BL | Blue | 2.80 mm | 0.79 | 0.95 | 1.11 | 1.27 |
PPN-RD | Red | 2.95 mm | 0.87 | 1.03 | 1.21 | 1.4 |
PPN-OR | Orange | 3.05 mm | 0.9 | 1.11 | 1.29 | 1.48 |
PPN-BK | Black | 3.25 mm | 0.98 | 1.21 | 1.4 | 1.6 |
Replacement pin for the Pin-Perfect Nozzle. The color of the pin designates the nozzle output rate. Replace pins with the same color as the original pin color. The diameter of the orifice in the black body of the Pin-Perfect Nozzle determines the flow rate for that nozzle. All pins have the same diameter and do not affect flow rate. Specify two letter color code when ordering.
ITEM | COLOR | SIZE |
PPNP-360 | - | - |
The Dramm 180_ Pin replaces any color pin on the Pin Perfect Nozzles. This allows for a 180_ pattern without changing nozzles. As the flow rate for the Pin Perfect Nozzle is controlled by the diameter of the nozzle body. The 180_ Pin offers a 180_ pattern without changing the flow. Color: black.
ITEM | COLOR | SIZE |
PPNP-180 | - | - |
Dramm 360_ Nifty Nozzles offer an economical solution for simple ÃÃoverheadÃ_ or ÃÃon the benchÃ_ watering systems. These ÃÃniftyÃ_ nozzles produce a 10 foot diameter spray pattern when your water pipeline is 5 feet above the crop. Nifty Nozzles can be installed on the topside of the pipeline, on bottom side of the pipeline or on top of 1/2 PVC risers. Bottom side installations require No-Drip Check Valves to prevent drip.
To provide uniform coverage the nozzles should be spaced so that their spray patterns overlap. With the pipeline 5 feet over your crop, Nifty Nozzles will produce a 10 foot diameter spray pattern. Space each nozzle 5 feet apart so the spray pattern will overlap to the next nozzle. Multiple pipelines should be spaced 10 feet apart for complete coverage. To decrease the spray diameter of the Nifty Nozzle to 7 feet, lower the water pipeline to 3 feet over the crop and space the nozzles at 3 1/2 foot intervals. Multiple pipelines should be spaced 7 feet apart for complete coverage.
For ÃÃon-the-benchÃ_ watering (for cut flower crops), we recommend using lower flow rate Brown, Green or Grey Nifty Nozzles spaced 3 feet apart, one pipeline down the center of each bench or bed.
Before you begin an installation, we recommend that you install one pipeline based on the guidelines presented. After the first pipeline is installed, tested and adjusted, remaining lines can be set-up following the same specifications as the first.
Use 360_ Nifty Nozzles in combination with Dramm Run-Out Valves, No-Drip Risers and No-Drip Extension Check Valves to control water drip.
ITEM | COLOR | SIZE | 15 PSI | 22 PSI | 29 PSI | 36 PSI |
360NN-BR | Brown | 1.75 mm | 0.29 | 0.35 | 0.41 | 0.46 |
ITEM | COLOR | SIZE | 15 PSI | 22 PSI | 29 PSI | 36 PSI |
360NN-GN | Green | 2.00 mm | 0.4 | 0.49 | 0.57 | 0.63 |
360NN-GR | Grey | 2.25 mm | 0.51 | 0.62 | 0.72 | 0.8 |
360NN-BL | Blue | 2.50 mm | 0.63 | 0.77 | 0.89 | 0.99 |
360NN-RD | Red | 2.75 mm | 0.76 | 0.93 | 1.07 | 1.2 |
360NN-OR | Orange | 3.00 mm | 0.9 | 1.1 | 1.28 | 1.43 |
An Assembly Insert is a threaded gasket that provides a quick installation and leak-free seal for Dramm Irrigation Nozzles. The interior female thread is 3/8 Witworth_ the same thread specification used on the Pin-Perfect, Nifty, Misty Mist and Drop style nozzles.
To Install, use a 7/16 drill bit to drill holes into schedule 40 PVC pipe, aluminum pipe or galvanized pipe. Caution: Do not use schedule 80 PVC. The Assembly Insert will not be able to create an effective seal due to the wall thickness of the schedule 80 PVC pipe.
Install the Assembly Insert into the hole and then screw in the nozzle. The width of the nozzle expands the Assembly Insert as it is screwed into place_ creating a leak-free seal without having to drill and tap every hole. Pipes should be clamped and drilled using a drill press or alignment jig to ensure perfectly round holes and straight alignment. Recommended for use at operating pressures up to 50 PSI.
ITEM | COLOR | SIZE |
AI | - | - |
Dramm 360_ Misty Mist Nozzles are for overhead mist propagation, irrigating plugs or raising humidity levels. Misty Mist Nozzles produce a 6 foot diameter spray pattern when your water pipeline is 5 feet above the crop.
Misty Mist Nozzles can be installed on the topside of the pipeline, on bottom side of the pipeline or on top of 1/2 PVC risers. Bottom side installations require No-Drip Check Valves to prevent drip.
To provide uniform coverage in overhead mist propagation or plug irrigation, the nozzles should be spaced so that their spray patterns overlap. With the pipeline 5 feet over your crop, Misty Mist Nozzles will produce a 6 foot diameter spray pattern. Space each nozzle 3 feet apart so the spray pattern will overlap to the next nozzle. Multiple pipelines should be spaced 6 feet apart for complete coverage. To decrease the spray diameter of the Misty Mist to 5 feet, lower the water pipeline to 3 feet over the crop and space the nozzles at 2 1/2 foot intervals. Multiple pipelines should be spaced 5 feet apart for complete coverage.
For raising humidity levels or mist cooling, use Blue/White Misty Mist Nozzles. It is recommended that you automate the system using short ÃÃonÃ_ cycle times due the relatively high output rate of the nozzle. The pipeline should be suspended as high as possible in the middle of each bay without interfering with the spray pattern. Space nozzles 6 feet apart. There is no need to worry about overlapping spray patterns since the goal is to evaporate water into the air versus allowing the water to drop to the soil.
Before you begin an installation, we recommend that you install one pipeline based on the guidelines presented. After the first pipeline is installed, tested and adjusted, remaining lines can be set-up following the same specifications as the first.
Use 360_ Misty Mist Nozzles in combination with Dramm Run-Out Valves, No-Drip Risers and No-Drip Extension Check Valves to control water drip.
ITEM | COLOR | SIZE | 36 PSI | 73 PSI |
MM-BW | Blue / White | 1.00 mm | 0.17 | 0.22 |
ITEM | COLOR | SIZE | 36 PSI | 73 PSI |
MM-RW | Red / White | 1.25 mm | 0.27 | 0.35 |
MM-KW | Black / White | 1.50 mm | 0.39 | 0.5 |
The High Pressure Misty Mist delivers an ultra fine spray_ ideal for mist cooling and raising humidity levels. These nozzles create a 10 foot diameter spray pattern.
High Pressure Misty Mist Nozzles should only be installed on the topside of the pipeline. Bottom side installations are not recommended due to the high pressures involved.
Space nozzles 10 feet apart with the pipeline suspended as high as possible in the middle of each bay_ without interfering with the spray pattern of the nozzle. There is no need to worry about overlapping spray patterns since the goal is to evaporate water into the air versus allowing the water to drop to the soil.
Please note that high pressure pumps and filtration equipment are required for these nozzles to work properly. High Pressure Misty Mist Nozzles can not be installed using Assembly Inserts. Threads must be tapped directly into the water pipeline_ use the drill & tap installation method explained at the end of this section.
Before you begin an installation, we recommend that you install one pipeline based on the guidelines presented. After the first pipeline is installed, tested and adjusted, remaining lines can be set-up following the same specifications as the first.
Use High Pressure 360_ Misty Mist Nozzles in combination with Dramm Run-Out Valves to control water drip.
ITEM | COLOR | SIZE | 73 PSI | 145 PSI | 290 PSI | 435 PSI |
HP-GW | Grey / White | 0.75 mm | 0.12 | 0.19 | 0.24 | 0.27 |
Due to a special spinning mechanism which increases the spray diameter of the Drop Inversion Nozzle_ it is perfect for 24 foot wide quonset/ tunnel houses. It is used on overhead watering systems that require a larger droplet size or an extended coverage area from each nozzle. Drop Inversion Nozzles produce a 360_ 24 foot diameter spray pattern and must be installed on the bottom side of the pipeline with No-Drip Extension Check Valves.
To provide uniform coverage the nozzles should be spaced so that their spray patterns overlap. With the pipeline 5 feet over your crop, Drop Inversion Nozzles produce a 24 foot diameter spray pattern. Space each nozzle 12 feet apart so the spray pattern will overlap to the next nozzle. Multiple pipelines should be spaced 24 feet apart for complete coverage. To decrease the spray diameter, lower the water pipeline until the desired spray diameter is achieved.
Before you begin an installation, we recommend that you install one pipeline based on the guidelines presented. After the first pipeline is installed, tested and adjusted, remaining lines can be set-up following the same specifications as the first.
Use Drop Inversion Nozzles in combination with Dramm Run-Out Valves and No-Drip Extension Check Valves to control water drip.
ITEM | COLOR | SIZE | 22 PSI | 29 PSI | 36 PSI |
DDI-GG | Grey / Grey | 2.25 mm | 0.62 | 0.71 | 0.8 |
The Drop Upright Nozzle has a unique spinning mechanism which increases the spray diameter of this nozzle to 30 feet when your water pipeline is 5 feet above the crop. It is used on overhead watering systems that require a larger droplet size or an extended coverage area from each nozzle. Drop Upright Nozzles produce a 360_ 36 foot diameter spray pattern and must be installed on the topside of the pipeline or on top of 1/2 PVC risers.
To provide uniform coverage the nozzles should be spaced so that their spray patterns overlap. With the pipeline 5 feet over your crop, Drop Upright Nozzles produce a 30 foot diameter spray pattern. Space each nozzle 15 feet apart so the spray pattern will overlap to the next nozzle. Multiple pipelines should be spaced 30 feet apart for complete coverage. To decrease the spray diameter, lower the water pipeline until the desired spray diameter is achieved.
Before you begin an installation, we recommend that you install one pipeline based on the guidelines presented. After the first pipeline is installed, tested and adjusted, remaining lines can be set-up following the same specifications as the first.
Use Drop Upright Nozzles in combination with Dramm Run-Out Valves, No-Drip Risers and No-Drip Extension Check Valves to control water drip.
ITEM | COLOR | SIZE | 22 PSI | 29 PSI | 36 PSI |
DDU-GB | Grey / Black | 2.25 mm | 0.62 | 0.71 | 0.8 |
The T-Drop Nozzle was created for long narrow installations in which an elliptical spray pattern is desired. T-Drop Nozzles can be installed on the topside of the pipeline, on bottom side of the pipeline or on top of 1/2 PVC risers. Bottom side installations require No-Drip Check Valves to prevent drip.
To provide uniform coverage the nozzles should be spaced so that their spray patterns overlap. With the pipeline 5 feet over your crop and nozzles installed on the topside of your pipeline, T-Drop Nozzles will produce a 10 foot by 5 foot elliptical spray pattern. Space each nozzle 5 feet apart so the spray pattern will overlap to the next nozzle. Multiple pipelines should be spaced 5 feet apart for complete coverage. To increase the spray diameter of the T-Drop to 12 feet by 6 feet, install the nozzles on the bottom side of the pipeline and space the nozzles at 6 foot intervals. Multiple pipelines should be spaced 6 feet apart for complete coverage.
Before you begin an installation, we recommend that you install one pipeline based on the guidelines presented. After the first pipeline is installed, tested and adjusted, remaining lines can be set-up following the same specifications as the first.
Use T-Drop Nozzles in combination with Dramm Run-Out Valves, No-Drip Risers and No-Drip Extension Check Valves to control water drip.
ITEM | COLOR | SIZE | 15 PSI | 22 PSI | 29 PSI | 36 PSI |
TDN | Brown / Red | 1.75 mm | 0.29 | 0.35 | 0.41 | 0.46 |
Oops! Did you drill one too many holes? Use the Dramm Nozzle Plug to cap off unwanted holes without replacing entire pipelines. Install as you would any other Dramm Nozzle or unscrew the unwanted Pin-Perfect, Nifty or Misty Mist Nozzle and simply replace it with the Nozzle Plug. Order a few extra_ we won't tell. Item Number: PLUG
ITEM | COLOR | SIZE |
PLUG | White | Universal |
The Dramm Hanging Nozzle system combines the superior flow rates and water patterns of Dramm nozzles with the flexibility of a below basket hanging irrigation system. Designed for misting or irrigation of crops on benches or on the ground, the Hanging Nozzle system uses the familiar Dramm nozzles with our No Drip Extension Check Valve and a leader tube.
Hanging nozzle systems offer solutions to the traditional problems of rigid pipe mounted irrigation systems. Hanging nozzle systems use a check valve and hang below the lateral which prevents dripping from the nozzle or the ÃÃshadowÃ_ dripping from the lateral. Dramm Hanging Nozzle Assemblies offer even watering. Gravity ensures that the nozzles are plumb preventing pattern distortion.
The entire assembly includes a leader tube with a barb fitting. The system uses flexible polyethylene tubing instead of PVC for ease of use and flexibility. A variety of leader tube lengths and nozzle choices are available. For flow rates see the specific nozzles.
To install a Dramm Pin-Perfect Hanging Nozzle System. Space the nozzle assemblies at 3_Ã spacings . Choose a leader tube length that places the nozzles below the hanging baskets or at a height of at least 3_Ã above the crop. Choose a Pin-Perfect Nozzle to suit your needs taking into account the flow rate of each nozzle and the flow rate of the lateral.
ITEM | COLOR | SIZE |
HNP-__-36 | - | 36 inch |
ITEM | COLOR | SIZE |
HNP-__-48 | - | 48 inch |
HNP-__-60 | - | 60 inch |
180_ spray pattern. Push into flexible 1/2 black poly tubing for perimeter watering. Use in conjunction with 90_ Nylon Nozzle.
ITEM | COLOR | SIZE |
180NY-RD | Red | - |
90_ spray pattern. Push into flexible 1/2 black poly tubing for perimeter watering. Use in conjunction with 180_ Nylon Nozzle.
ITEM | COLOR | SIZE |
90NY-GR | Grey | - |
No-Drip Risers elevate Dramm Irrigation Nozzles 2 1/4 above the PVC pipeline. When pipeline water flow is shut-off, excess water falls back into the pipeline due to the height of the No-Drip Riser. This ÃÃfall backÃ_ helps control drip from nozzles overhead. No-Drip Risers can also be used to elevate Dramm Irrigation Nozzles above the soil line when pipes are buried for landscape purposes.
ITEM | COLOR | SIZE |
NDR | - | - |
No-Drip Risers elevate Dramm Irrigation Nozzles 2 1/4 above the PVC pipeline. When pipeline water flow is shut-off, excess water falls back into the pipeline due to the height of the No-Drip Riser. This ÃÃfall backÃ_ helps control drip from nozzles overhead. No-Drip Risers can also be used to elevate Dramm Irrigation Nozzles above the soil line when pipes are buried for landscape purposes.
ITEM | COLOR | SIZE |
NDECV | - | - |
Run-Out Valves are designed to be installed at the end of 1-inch or 3/4-inch PVC pipelines. When the water is turned off, the Run-Out Valve will open and allow water to run out of the line_ eliminating drip from all overhead nozzles. Run-Out Valves require at least 15 PSI to work properly.
Use PVC cement and a 1 to 3/4 PVC reducer bushing to connect Run-Out Valves to 3/4-inch PVC pipelines. Follow the PVC cement directions regarding pipe preparation and drying times.
ITEM | COLOR | SIZE |
ROV | - | - |
The Threaded Pipe Nipple is used to attach Dramm Irrigation Nozzles directly to 1/2 PVC pipe risers. To install, simply screw the Threaded Pipe Nipple onto the threaded 1/2 PVC pipe riser. This method is ideal when you want to eliminate overhead lines or when overhead lines are impossible. 1/2 NPT X 3/8 WW . Use with 1/2 threaded PVC risers.
ITEM | COLOR | SIZE |
PN-2010 | - | - |
The Slip Fit Pipe Nipple is used to attach Dramm Irrigation Nozzles directly to straight (unthreaded) 1/2 PVC pipe risers. To install, use PVC cement to attach the Slip Fit Pipe Nipple onto PVC pipe risers. Follow the PVC cement directions regarding pipe preparation and drying times. This method is ideal when you want to eliminate overhead lines or when overhead lines are impossible. 1/2 NPT X 3/8 WW . Use with 1/2 straight PVC risers.
ITEM | COLOR | SIZE |
PN-2020 | - | - |
Creates a 3/8 Whitworth thread in PVC for Pin-Perfect, Nifty or Misty Mist Nozzles.
ITEM | COLOR | SIZE |
DT-N | - | - |
The Kwik Klamp is a bracket with a hinged clip that can open and close. This handy device locks shut when closed, but can be opened to remove or replace pipelines. The Kwik Klamp makes pipe installation fast and easy. Made in the Netherlands from chemical resistant polypropylene. Available for 3/4 and 1 diameter pipes. Metric and additional inch sizes are available upon special order. Use with the Kwik Spacer.
ITEM | COLOR | SIZE |
KK-75 | - | 3/4 in |
ITEM | COLOR | SIZE |
KK-100 | - | 1 in |
KK-125 | - | 1.25 in |
KK-150 | - | 1.5 in |
KK-200 | - | 2 in |
The Kwik Spacer slides into the Kwik Klamp and is used to create additional space between the pipe and wall. Multiple Kwik Spacers can be combined to create varying lengths in 3/4 increments. Made in the Netherlands from chemical resistant polypropylene. Available for 3/4 and 1 Kwik Klamps. Metric and additional inch sizes are available upon special order.
ITEM | COLOR | SIZE |
KS-75 | - | 3/4 in |
ITEM | COLOR | SIZE |
KS-100 | - | 1 in |
KS-125 | - | 1.25 in |
KS-150 | - | 1.5 in |
KS-200 | - | 2 in |
Dramm On Only Dribble Tubes have permanently attached always ON weight emitters. All On Dribble Tubes are permanently assembled. Different sizes and different lengths can be combined for price breaks.
There are three types of Dribble Tubes available: DTS with a .045 inside diameter green tube, DTM with a .060 inside diameter brown tube- and DTL with a .075 inside diameter blue tube. All 3 types are available in lengths from 12 TO 42 long. Use of Dribble Tubes allows individual pot watering for a total bench. Dramm Dribble Tubes should be used on 5, 6, or 7 pot sizes.
ITEM | COLOR | SIZE |
DTS-12 | Green Tubing | 12 in |
ITEM | COLOR | SIZE |
DTS-18 | Green Tubing | 18 in |
DTS-24 | Green Tubing | 24 in |
DTS-30 | Green Tubing | 30 in |
DTS-36 | Green Tubing | 36 in |
DTS-42 | Green Tubing | 42 in |
DTS-48 | Green Tubing | 48 in |
DTS-60 | Green Tubing | 60 in |
DTM-12 | Brown Tubing | 12 in |
DTM-18 | Brown Tubing | 18 in |
DTM-24 | Brown Tubing | 24 in |
DTM-30 | Brown Tubing | 30 in |
DTM-36 | Brown Tubing | 36 in |
DTM-42 | Brown Tubing | 42 in |
DTM-48 | Brown Tubing | 48 in |
DTM-60 | Brown Tubing | 60 in |
DTL-12 | Blue Tubing | 12 in |
DTL-18 | Blue Tubing | 18 in |
DTL-24 | Blue Tubing | 24 in |
DTL-30 | Blue Tubing | 30 in |
DTL-36 | Blue Tubing | 36 in |
DTL-42 | Blue Tubing | 42 in |
DTL-48 | Blue Tubing | 48 in |
DTL-60 | Blue Tubing | 60 in |
Dramm StixÃ_ are designed to be used when it is impossible to run overhead water lines but the grower wants to water or mist from overhead. Very useful on moveable benching! Dramm Stix are available in 5 different heights from 10 to 36 and include the poly tubing (-which is 30 longer than the stick-), Pin Perfect nozzles, and the Dramm Stixé. The orange base Dramm Stixsé allow you to change from water nozzles to mist nozzles.
Dramm Stixé have a 3/8 WW thread which accommodates the Pin Perfect, Nifty, Misty Mist, and 180_ Nifty Nozzles. Dramm stix come standard with green Pin Perfect Nozzles unless specific type and color-coded nozzle are requested. Nifty Nozzles spray a 7 ft. diameter circle- while Misty Mist Nozzles cover a 4.5 ft. diameter circle. Both will completely water 100 ft. of bench or bed in about 5 minutes. Water supply tubes are inserted at 42 inch intervals in 3/4 or 1 black polyethylene pipe. Benches up to 70ft. long- use 3/4 pipe, over 70 ft. long- use 1 pipe, over 120 ft. long- use 1 pipe with supply in middle.
ITEM | COLOR | SIZE |
SS-10 | - | 10 in |
ITEM | COLOR | SIZE |
SS-16 | - | 16 in |
SS-24 | - | 24 in |
SS-30 | - | 30 in |
SS-36 | - | 36 in |
Dramm Dribble Rings are designed for individual pot watering of larger size containers. The ring encircles the plant and water is emitted in 5 areas through 10 holes to ensure uniform watering in larger pot sizes. Dribble Rings come in 5 sizes with different length lead tubes: They are recommended for all plants in 6 & 7 containers, 8 - 10 containers, 13 containers, 16 containers, and the largest for use in 18 - 20 containers. Dramm Dribble Rings provide complete, uniform watering for large pots, B&B stock, tropical plantings and orchids.
Dribble Rings are fed with a .060 ID Tube. A maximum of 400 containers can be watered with the Dramm Dribble Rings from a 3/4 supply pipe. Minimum order 100 per size.
ITEM | COLOR | SIZE |
DR4-12 | - | 12 in |
ITEM | COLOR | SIZE |
DR4-24 | - | 24 in |
DR4-36 | - | 36 in |
DR4-48 | - | 48 in |
DR6-12 | - | 12 in |
DR6-24 | - | 24 in |
DR6-36 | - | 36 in |
DR6-48 | - | 48 in |
DR85-12 | - | 12 in |
DR85-24 | - | 24 in |
DR85-36 | - | 36 in |
DR85-48 | - | 48 in |
DR10-12 | - | 12 |
DR10-24 | - | 24 |
DR10-36 | - | 36 |
DR10-48 | - | 48 |
DR13-12 | - | 12 |
DR13-24 | - | 24 |
DR13-36 | - | 36 |
DR13-48 | - | 48 |
The Dramm Hand Pick Tool is used for the insertion of Dramm Brass Eyelets into poly tubbing for the use of Dramm Dribble Tubes and Rings. Place an eyelet onto the tip of the Handpik tool and push firmly into the black poly tubing. The Hand Pick Tool will pierce the poly tubing and insert the brass eyelet in one leak-free operation!
ITEM | COLOR | SIZE |
HPT | - | - |
Brass eyelet. Used to install Dramm Dribble Tubes and Dribble Rings.
ITEM | COLOR | SIZE |
DTMS-E | - | .060 or .045 ID |
Brass eyelet. Used to install Dramm Dribble Tubes and Dribble Rings.
ITEM | COLOR | SIZE |
DTL-E | - | .075 ID |
Small leader tube for Dramm Dribble Tubes.
ITEM | COLOR | SIZE |
O45 | Green | 5,000 feet/ roll |
Medium leader tube for Dramm Dribble Tubes.
ITEM | COLOR | SIZE |
O6O | Brown | 5,000 feet/ roll |
Large leader tube for Dramm Dribble Tubes.
ITEM | COLOR | SIZE |
O75 | Blue | 5,000 feet/ roll |
Dramm Stix leader tube.
ITEM | COLOR | SIZE |
192 | Black | 2,500 feet/ roll |
Dramm's ultra-durable solenoids are designed to outlast the competition and shut-off rapidly. Perfect for misting systems, where an extra second or two is more water than needed, the SVB range of solenoids are fast acting.
ITEM | COLOR | SIZE |
SVB075 | - | 3/4 in - 24VAC 1.2 W |
Dramm Solenoid Valve - 1 National Pipe Thread
ITEM | COLOR | SIZE |
SVB100 | - | 1 in - 24VAC 1.2 W |
SVB150 | - | 1.5 in - 24VAC 1.2 W |
SVB200 | - | 2 in - 24VAC 1.2 W |
Dramm PE tubing is available in 16mm and 25mm (3/4) in various lengths. Call for sizing and pricing.
ITEM | COLOR | SIZE |
PE tubing | - | 16mm or 25mm |
Dramm offers preassembled valve stations as well as multi line manifolds. Build with easy maintenance in mind, Dramm pre assembled PVC components make irrigation system installation easy. Talk to Dramm about designing your irrigation system today and include Dramm pre assembled system components.
ITEM | COLOR | SIZE |
Valve Station | - | - |
PolyRail aluminum extrusion tightly sleeves PE tubing keeping it rigid, without sags. PolyRail keeps nozzles straight and even, ensuring the best coverage for your irrigation system. Installs easily without glue.
ITEM | COLOR | SIZE |
ALU16 | - | 12' section |
25mm (3/4) diameter. For higher flow and more support. 25mm PolyRail may be used to hang baskets
ITEM | COLOR | SIZE |
ALU25 | - | 12' section |
Connecting band with set screws. 4 length. Connects two rail pieces together.
ITEM | COLOR | SIZE |
ALU501CB | - | 4 inch |
Connecting band with set screws. 14 length. Connects two rail pieces together.
ITEM | COLOR | SIZE |
ALU50135 | - | 14 inch |
Hanger to position PE outlet at a 90_ angle
ITEM | COLOR | SIZE |
ALU500PH | - | 16mm |
Hanger to position PE outlet at a 90_ angle
ITEM | COLOR | SIZE |
ALU500-90 | - | 25mm |
Hanger rides on Rail to position PE outlet towards the bottom of the Rail.
ITEM | COLOR | SIZE |
ALU502H | - | Top |
Stop used at both ends of each irrigation run. Includes set screw.
ITEM | COLOR | SIZE |
ALU541S | - | - |
Punch for centering 3mm hole in PE.
ITEM | COLOR | SIZE |
ALU503A | - | 25mm |
Punch for centering 3mm hole in PE.
ITEM | COLOR | SIZE |
ALU509A | - | 16mm |
Base for PolyRail Bench Riser Support
ITEM | COLOR | SIZE |
ALUSB | - | - |
Cap for top of PolyRail Bench Riser Support
ITEM | COLOR | SIZE |
ALUSC | - | - |
JetRain Nozzle Low Pressure with Clean Out Check Valve Barbed Inlet. For propagation mist. Alternate with Blue for best results.
ITEM | COLOR | SIZE |
JRLPC-B-WH | - | .48 gpm |
JetRain Nozzle Low Pressure with Clean Out Check Valve Barbed Inlet. For propagation mist. Alternate with White for best results.
ITEM | COLOR | SIZE |
JRLPC-B-BL | - | .48 gpm |
JetRain Nozzle Low Pressure with Clean Out Check Valve Barbed Inlet. For mist and irrigation.
ITEM | COLOR | SIZE |
JRLPC-B-RD | - | .79 gpm |
JetRain Nozzle Low Pressure with Clean Out Check Valve Barbed Inlet. For heavier irrigation.
ITEM | COLOR | SIZE |
JRLPC-B-YL | - | 1.37 gpm |
JetRain Nozzle Barbed with no Check Valve Barbed Inlet
ITEM | COLOR | SIZE |
JR-B | - | - |
JetRain Nozzle Low Pressure with Clean Out Check Valve Threaded Inlet. For propagation mist. Alternate with Blue for best results.
ITEM | COLOR | SIZE |
JRLPC-T-WH | - | .48 gpm |
JetRain Nozzle Low Pressure with Clean Out Check Valve Threaded Inlet. For propagation mist. Alternate with White for best results.
ITEM | COLOR | SIZE |
JRLPC-T-BL | - | .48 gpm |
JetRain Nozzle Low Pressure with Clean Out Check Valve Threaded Inlet. For mist and irrigation.
ITEM | COLOR | SIZE |
JRLPC-T-RD | - | .79 gpm |
JetRain Nozzle Low Pressure with Clean Out Check Valve Threaded Inlet. For heavier irrigation.
ITEM | COLOR | SIZE |
JRLPC-T-YL | - | 1.37 gpm |
JetRain Nozzle Threaded with no Check Valve Threaded Inlet
ITEM | COLOR | SIZE |
JR-T | - | - |
JetRain 180 deg Pattern Barbed - Choose a color
ITEM | COLOR | SIZE |
JRLPC180-B-_ | - | - |
JRLPC180-T-_ | - | - |
JRC180-_ _ | - | - |
JR180-_ _ | - | - |
Replacement pin are specific to each nozzle. Please specify color when ordering.
ITEM | COLOR | SIZE |
JR-P-_ _ | - | - |
Check valve for JetRain nozzle with cleanout. 15-50 psi.
ITEM | COLOR | SIZE |
JR-807L | - | - |
Check valve for JetRain nozzle with cleanout. 15-50 psi.
ITEM | COLOR | SIZE |
JR-808L | - | - |
Jet Rain installation and care manual.
ITEM | COLOR | SIZE |
Manual | - | - |
JR-539 | - | - |
JR-566 | - | - |
JR-528 | - | - |
Add to a JetRain assembly to turn individual nozzles on and off.
ITEM | COLOR | SIZE |
JRBV-750 | - | - |
The JefFog nozzle offers a very fine spray (80 micron) between 50-70 psi. Available in a barbed or threaded inlet with single or multiple outlets. Flow per tip is 5.8 lph (1.5 gph).
ITEM | COLOR | SIZE |
JFSB | - | - |
The JefFog nozzle offers a very fine spray (80 micron) between 50-70 psi. Available in a barbed or threaded inlet with single or multiple outlets. Flow per tip is 5.8 lph (1.5 gph).
ITEM | COLOR | SIZE |
JFST | - | - |
Two outlet nozzle with barbed inlet. Flow rate is 11.6 lph (3 gph).
ITEM | COLOR | SIZE |
JFB2 | - | - |
Four outlet nozzle with barbed inlet. Flow rate is 23.2 lph (6 gph).
ITEM | COLOR | SIZE |
JFSB4 | - | - |
Five outlet nozzle with barbed inlet. Flow rate is 29 lph (7.5 gph).
ITEM | COLOR | SIZE |
JFSB5 | - | - |
Four outlet nozzle with threaded inlet. Flow rate is 23.2 lph (6 gph).
ITEM | COLOR | SIZE |
JFST4 | - | - |
Five outlet nozzle with threaded inlet. Flow rate is 29 lph (7.5 gph).
ITEM | COLOR | SIZE |
JFST5 | - | - |
Installation and care manual for JetFog nozzles.
ITEM | COLOR | SIZE |
Manual | - | - |
Replacement nozzle tip for JetFog nozzle. Press-fit connection.
ITEM | COLOR | SIZE |
JF-525 | - | - |
Blank nozzle tip to prevent spray from any JetFog outlet. Press-fit connection.
ITEM | COLOR | SIZE |
JF-524 | - | - |
Two way cross for JetFog Nozzle. Press fit connection.
ITEM | COLOR | SIZE |
JF-2CROSS | - | - |
Four way cross for JetFog Nozzle. Press fit connection.
ITEM | COLOR | SIZE |
JF-4CROSS | - | - |
Replacement diaphragm for JetFog Anti Drip Device. Silicone. Use JF-WRENCH-C to access diaphragm and reseat new diaphragm.
ITEM | COLOR | SIZE |
JF-560 | - | - |
Includes JF-WRENCH & BLANK tool, 10 BLANK6, 5 JF-525, 3 JF-524, 5 JF-560
ITEM | COLOR | SIZE |
JF-KIT | - | kit |
Combo set for disassembling and reassembling JetFOG nozzles easily.
ITEM | COLOR | SIZE |
JF-WRENCH-C | - | - |
The ii ri Smart Controller is a a battery operated, Bluetooth Connected, irrigation/misting controller that can oprate one solenoid valve without wiring.
Create different programs on your smartphone and upload them to your ii ri easily to change scenarios. Great for quick installations, single propagation benches, outdoor mum fields and more.
ITEM | COLOR | SIZE |
iiri3v | - | 3/4 in. valve |
Ii ri Smart Controller including 3/4 solenoid valve.
ITEM | COLOR | SIZE |
iiriSVB075 | - | 3/4 in. valve |
iiriSVB100 | - | 1 in. valve |
The Dramm MistTime Controller is perfect for time or temperature based control of misting valves. With the ability to program each valve independently, the MistTime offers unmatched flexibility. Each valve is operated on a cycle. The timing is variable with the duration operating between 1 second and 60 minutes and the interval time operating between 1 minute and 12 hours. Each valve can be run continuously, between specific times, or even started when the temperature rises above a set point. With the ability to program each valve independently, the controller can operate as a time based mist controller, a pulse-irrigation controller and a mist cooling controller at the same time. In addition, the MistTime offers the option to convert the last valve output to a pump pre-start output. When configured in this manner, the operator is given an option to pre-start a pump prior to any valve operation. The pre-start time is variable. This ensures that the system is properly pressurized when the mist system is in operation. The MistTime is easy to program using a keypad to navigate the menu and enter amounts. For flexibility, the MistTime can be programmed in English, Spanish, French or Dutch. The MistTime operates on 120vAC or 220vAC and includes a 24vAC output. The unit is enclosed in a NEMA 4 rated PVC housing and is easy to wire and install.
ITEM | COLOR | SIZE |
MT-10 | - | 10 Output |
The MistTime is programmable in English, Spanish, French and Dutch. This manual offers native language support.
ITEM | COLOR | SIZE |
MT-10 Manual ESP | - | - |
MT-10 Manual FRA | - | - |
MT10-TP | - | - |
The ProLine Irrigation Controller offers advanced control features such as multiple program operation, master valve, multiple start times per day, manual operation, and an option to add cellular connectivity to monitor and modify irrigation operation from your phone.
ITEM | COLOR | SIZE |
PL1600-04 | - | 4 output |
Quick Start Guide for the ProLine Controller. Step-by-step instructions to program the basics.
ITEM | COLOR | SIZE |
ProLineQS | - | Document |
Easy instructions showing how to install your ProLine Controller.
ITEM | COLOR | SIZE |
ProLineIG | - | Document |
ITEM | COLOR | SIZE |
PL1600-08 | - | 8 output |
PL1600-12 | - | 12 output |
PL1600-12B | - | 12 output (base) |
PL1600-16 | - | 16 output |
PL1600-20 | - | 20 output |
PL1600-24 | - | 24 output |
PL-1600-M4 | - | 4 output module |
PL-1600-M12 | - | 12 output module |
PL-SLAC | - | - |
PL-SLAC-50 | - | - |
PL-420LS | - | - |
The RainPro has been discontinued. The manual remains on line for previous customers.
ITEM | COLOR | SIZE |
RPIC-Manual | - | - |
The RainPro has been discontinued. However, we still have 4 output modules to upgrade existing units. This module fits into open slots in the RainPro 03, 07 and 11 version to add 4 outputs to increase the capacity of the unit.
ITEM | COLOR | SIZE |
RPIC-M4 | - | 4 Outputs |
ITEM | COLOR | SIZE |
PCAS2L-18 | - | 18 in |
ITEM | COLOR | SIZE |
PCAS2L-24 | - | 24 in |
PCAS2L-36 | - | 36 in |
PCAS2L-48 | - | 48 in |
2 liter per hour emitter with barbed outlet for attaching to 0.191 tubing. Offering even flow rates at variable pressures, PCAS emitters provide even water from the first to the last dripper. Our LARGER emitter body allows for a wider labyrinth that prevents clogging by letting debris pass through the emitter.
ITEM | COLOR | SIZE |
PCAS2L | - | 2 lph |
4 liter per hour emitter with barbed outlet for attaching to 0.191 tubing. Offering even flow rates at variable pressures, PCAS emitters provide even water from the first to the last dripper. Our LARGER emitter body allows for a wider labyrinth that prevents clogging by letting debris pass through the emitter.
ITEM | COLOR | SIZE |
PCAS4L | - | 4 lph |
4 liter per hour emitter with barrel outlet for attaching to 0.191 tubing. Offering even flow rates at variable pressures, PCAS emitters provide even water from the first to the last dripper. Our LARGER emitter body allows for a wider labyrinth that prevents clogging by letting debris pass through the emitter.
ITEM | COLOR | SIZE |
PCAS4L-B | - | 4 lph |
8 liter per hour emitter with barrel outlet for attaching to 0.191 tubing. Offering even flow rates at variable pressures, PCAS emitters provide even water from the first to the last dripper. Our LARGER emitter body allows for a wider labyrinth that prevents clogging by letting debris pass through the emitter.
ITEM | COLOR | SIZE |
PCAS8L | - | 8 lph |
12 liter per hour emitter with barrel outlet for attaching to 0.191 tubing. Offering even flow rates at variable pressures, PCAS emitters provide even water from the first to the last dripper. Our LARGER emitter body allows for a wider labyrinth that prevents clogging by letting debris pass through the emitter.
ITEM | COLOR | SIZE |
PCAS12L | - | 12 lph |
Connect barrel outlet emitters to 192 tubing with this adaptor.
ITEM | COLOR | SIZE |
MAN1 | - | 1 outlet 3mm barb |
Dramm 2 and 4 Way Manifolds are for use with the MB 4LPH and 8LPH emitters. The Manifolds allow multiple pots to be watered from one emitter.
ITEM | COLOR | SIZE |
MAN2 | - | 2 outlet 3mm barb |
Dramm 2 and 4 Way Manifolds are for use with the MB 4LPH and 8LPH emitters. The Manifolds allow multiple pots to be watered from one emitter.
ITEM | COLOR | SIZE |
MAN4 | - | 4 outlet 3mm barb |
ITEM | COLOR | SIZE |
PCASW | - | 11 Gram |
ITEM | COLOR | SIZE |
191-18 | Black | 18 in. |
191-24 | Black | 24 in. |
191-36 | Black | 35 in. |
191-42 | Black | 42 in. |
191-48 | Black | 48 in. |
Pressure Compensated Rings offer even watering of trees and nursery stock. With a choice of 4 lph (1 gph), 8 lph (2 gph), or 12 lph (4 gph) emitters, each plant gets the same amount of water supplied by Dramm's Dribble Rings.
ITEM | COLOR | SIZE |
PCR4-12 | - | 12 in. tube |
ITEM | COLOR | SIZE |
PCR4-24 | - | 24 in. tube |
PCR4-36 | - | 36 in. tube |
PCR4-48 | - | 48 in. tube |
PCR6-12 | - | 12 in. tube |
PCR6-24 | - | 24 in. tube |
PCR6-36 | - | 36 in. tube |
PCR6-48 | - | 48 in. tube |
PCR85-12 | - | 12 in. tube |
PCR85-24 | - | 24 in. tube |
PCR85-36 | - | 36 in. tube |
PCR85-48 | - | 48 in. tube |
PCR10-12 | - | 12 in. tube |
PCR10-24 | - | 24 in. tube |
PCR10-36 | - | 36 in. tube |
PCR10-48 | - | 48 in. tube |
PCR13-12 | - | 12 in. tube |
PCR13-24 | - | 24 in. tube |
PCR13-36 | - | 36 in. tube |
PCR13-48 | - | 48 in. tube |
The S3ANCHOR holds dribble rings in the pot, keeping them optimally placed for best water distribution.
ITEM | COLOR | SIZE |
S3ANCHOR | - | 6 |
The T-Piece has two barbed, secure connections and one smooth connection to allow for the ring to be easily disconnected.
ITEM | COLOR | SIZE |
T-PIECE | - | - |
Barbed Microvalve for drip irrigation. Allows individual pressure compensated drippers to be turned off.
ITEM | COLOR | SIZE |
MTMV-25 | - | 1/4 in barbs |
Barbed fitting
ITEM | COLOR | SIZE |
BARB3 | - | 3mm |
Plug for mistakes when using the 3mm barbed fitting.
ITEM | COLOR | SIZE |
BLANK3 | - | 3mm |
Multi-tool for irrigation installation. Cuts PE, punches holes with 3,4,5 mm blades. Inserts barbed components into PE.
ITEM | COLOR | SIZE |
ML-TOOL | - | Multi |
Easy-to-use 3mm Punch for 16mm or 1/2 Tubing
ITEM | COLOR | SIZE |
PUNCH1650 | - | 3mm |
Replaces standard blade when worn.
ITEM | COLOR | SIZE |
PUNCH1650-B | - | 3mm |
Plain barbed stake
ITEM | COLOR | SIZE |
ST-45 | - | 4 in. |
Labyrinth Stake
ITEM | COLOR | SIZE |
LST4-45 | - | 4 in. |
Easyloc Inline Valve 16mm x 16mm. Shuts off PE line. Insert as needed. Barb & Compression nut. Needs no additional clamp.
ITEM | COLOR | SIZE |
ITVSL16 | - | 16mm x 16mm |
Easyloc Inline Valve 16mm x 3/4in. MPT. Connect PVC to PE. Barb & Compression nut. Needs no additional clamp.
ITEM | COLOR | SIZE |
ITV075SL16 | - | 16mm x 3/4in |
Easyloc Fitting 16mm x 3/4in. MPT. Connect PVC to PE. Barb & Compression nut. Needs no additional clamp.
ITEM | COLOR | SIZE |
ITF075SL16 | - | 16mm x 3/4in |
Easyloc Tee 16mm. Barb & Compression nut. Needs no additional clamp.
ITEM | COLOR | SIZE |
ITTSL16 | - | 16mm |
Easyloc Elbow 16mm. Barb & Compression nut. Needs no additional clamp.
ITEM | COLOR | SIZE |
ITESL16 | - | 16mm |
Easyloc Coupling 16mm. Barb & Compression nut. Needs no additional clamp.
ITEM | COLOR | SIZE |
ITCSL16 | - | 16mm |
Figure 8 clamp to close 16mm PE ends.
ITEM | COLOR | SIZE |
600AP8 | - | 16mm |
Floraplus 2 (1L/m2 - cap mat & PP ground cover) 72 x 100' Roll
ITEM | COLOR | SIZE |
FP2-72X100 | - | 72 in |
FP3-72X100 | - | 72 in |
FP2-48X100 | - | 48 in |
FP3-48X100 | - | 48 in |
FP2-96X100 | - | 96 in |
Vivaplus 2 (3L/m2 - cap mat & PP ground cover)) 72 x 100' Roll
ITEM | COLOR | SIZE |
VP2-72X100 | - | 72 in |
VP3-72X100 | - | 72 in |
VP2-48X100 | - | 48 in |
VP3-48X100 | - | 48 in |
VP2-96X100 | - | 96 in |
Aquafol Filter Cloth - White 79 x 164' Roll
ITEM | COLOR | SIZE |
AFW-79X164 | - | 79 in |
AFW-48X100 | - | 48 in |
Strand Dripper 12 lph flow rate with 18 inch perforated tube.
ITEM | COLOR | SIZE |
ST18-A112 | - | 18 in |
ST24-A112 | - | 36 in |
ST30-A116 | - | 36 in |
ST42-A116 | - | 42 in |
ST30-A124 | - | 30 in |
ST42-A124 | - | 42 in |
STP12-A208 | - | 12 in |
STP18-A208 | - | 18 in |
STP18-A212 | - | 18 in |
STP24-A212 | - | 24 in |
STP30-A216 | - | 30 in |
STP42-A216 | - | 42 in |
STP30-A224 | - | 30 in |
STP42-A224 | - | 42 in |
#10,11,12,13,14,15,16,17,18,20 - Green #1, Black#2, Gray#3
ITEM | COLOR | SIZE |
N-12884-11XX | - | - |
#40, 45, 50, 55, 60 - Red #1 , White #2, Orange #7
ITEM | COLOR | SIZE |
N-9913-11XX | - | - |
#10,11,12,13,14,15,16,18,20 - Blue #10, Purple #12, Green #14, Red #16, Yellow #18, Brown #20 Purple, Ivory
ITEM | COLOR | SIZE |
N-9928-10XX | - | - |
#10,11,12,13,14,15,16,17,18,20 - Standard flat Black plate
ITEM | COLOR | SIZE |
N-12928-10XX | - | - |
N-9914-13XX | - | - |
N-12927-11XX | - | - |
N-9929-10XX | - | - |
N-13827-12XX | - | - |
ITEM | COLOR | SIZE |
N-12213-001 | - | - |
The Abot Riser base connects laterals to risers.
ITEM | COLOR | SIZE |
A-050-001-607 | - | 1.5 in |
Male PipeLoc fitting.
ITEM | COLOR | SIZE |
A-050-001-616 | - | 1.5 in |
Female PipeLoc fitting.
ITEM | COLOR | SIZE |
A-050-001-517 | - | 1.5 in |
20 inch riser section for PipeLoc. Threads into Riser Base and connects to other riser pipes to reach desired nozzle height.
ITEM | COLOR | SIZE |
A-032-032-450 | - | - |
ITEM | COLOR | SIZE |
A-063-001-607 | - | 2 in |
A-075-001-607 | - | 2.5 in |
A-090-001-607 | - | 3 in |
A-050-050-621 | - | 1.5 in |
A-063-063-623 | - | 2 in |
A-075-050-624 | - | 2.5 in/1.5 in |
A-075-063-625 | - | 2.5 in/2 in |
A-075-075-626 | - | 2.5 in |
A-090-050-627 | - | 3 in/1.5in |
A-090-063-628 | - | 3in/2in |
A-090-075-629 | - | 3in/2.5in |
A-090-090-630 | - | 3 in |
A-050-050-642 | - | 1.5 in |
A-063-063-644 | - | 2 in |
A-075-050-645 | - | 2.5 in/1.5 in |
A-075-063-646 | - | 2.5 in/2 in |
A-075-075-647 | - | 2.5 in |
A-090-050-648 | - | 3 in/1.5in |
A-090-063-649 | - | 3 in/2 in |
A-090-075-650 | - | 3 in/2.5 in |
A-090-090-651 | - | 3in |
A-063-050-665 | - | - |
A-075-050-666 | - | - |
A-075-063-667 | - | - |
A-090-050-668 | - | - |
A-090-063-669 | - | - |
A-090-075-670 | - | - |
A-050-000-608 | - | - |
A-063-000-608 | - | - |
A-075-000-608 | - | - |
A-090-000-608 | - | - |
A-050-000-509 | - | 1.5 in |
A-063-000-509 | - | 2 in |
A-075-000-509 | - | 2.5 in |
A-090-000-509 | - | 3 in |
A-063-001-616 | - | 2 in |
A-075-001-616 | - | 2.5 in |
A-090-001-616 | - | 3 in |
A-063-001-517 | - | 2 in |
A-075-001-517 | - | 2.5 in |
A-090-001-517 | - | 3 in |
A-050-000-605 | - | 1.5 in |
A-063-000-605 | - | 2 in |
A-075-000-605 | - | 2.5 in |
A-030-000-605 | - | 3 in |
A-050-000-506 | - | 1.5 in |
A-063-000-506 | - | 2 in |
A-075-000-506 | - | 2.5 in |
A-030-000-506 | - | 3 in |
A-032-025-001 | - | - |
A-032-032-014 | - | - |
A-050-000-612 | - | 1.5 in |
A-063-000-612 | - | 2 in |
A-075-000-612 | - | 2.5 in |
A-090-000-612 | - | 3 in |